NAGIOS: RODERIC FUNCIONANDO

Bonding efficacy of an acetone/based etch-and-rinse adhesive after dentin deproteinization

Repositori DSpace/Manakin

IMPORTANT: Aquest repositori està en una versió antiga des del 3/12/2023. La nova instal.lació está en https://roderic.uv.es/

Bonding efficacy of an acetone/based etch-and-rinse adhesive after dentin deproteinization

Mostra el registre parcial de l'element

dc.contributor.author Aguilera, Fátima S. es
dc.contributor.author Osorio Ruiz, R. es
dc.contributor.author Osorio, Estrella es
dc.contributor.author Moura, Pedro es
dc.contributor.author Toledano Pérez, Manuel es
dc.date.accessioned 2017-07-24T12:11:13Z
dc.date.available 2017-07-24T12:11:13Z
dc.date.issued 2012 es
dc.identifier.citation Aguilera, Fátima S. ; Osorio Ruiz, R. ; Osorio, Estrella ; Moura, Pedro ; Toledano Pérez, Manuel. Bonding efficacy of an acetone/based etch-and-rinse adhesive after dentin deproteinization. En: Medicina oral, patología oral y cirugía bucal. Ed. inglesa, 17 4 2012: 2- es
dc.identifier.uri http://hdl.handle.net/10550/59897
dc.description.abstract Objectives: to evaluate the effect of sodium hypochlorite (NaOCl) treatment on dentin bonding by means of shear bond strength (SBS) measurements when using Prime and Bond NT (PB NT) adhesive. Ultrastructure of the interfaces was examined by scanning electron microscopy (SEM). Study design: Extracted human third molars were sectioned and ground to expose flat surfaces of superficial or deep dentin. Specimens were randomly assigned to two equal groups, and bonded as follows: (1) according to the manufacturers? directions, after 35% H 3 PO 4 etching, (2) 5% NaOCl treated for 2 minutes, after 35% H 3 PO 4 etching. Each sample was embedded in a Watanabe shear test assembly for a single plane lap shear. After PB NT bonding, specimens were stored in water for 24 h at 37ºC and thermocycled (500x). Samples were tested in shear to failure using a universal testing machine at 0.75 mm/ min. Data were analyzed with ANOVA and Newman-Keuls multiple comparison test procedures. Two samples of each group were randomly selected to investigate the morphologic aspect of the resin/dentin interface with SEM. Results: After etching and after aqueous sodium hypochlorite (NaOCl aq ) application, SBS values were similar on superficial than deep dentin (p>0.05). SEM findings shows for H 3 PO 4 etching conditioned samples a detectable hybrid layer and long resin tags; for NaOCl treated specimens, it may be observed a non apparent hybrid layer, and the adhesive contact directly with the neck of the cylindrical resin tags. Conclusions: The use of 5% NaOCl for 2 min after dentin demineralization when PB NT was employed did not improve the bond strength to dentin, probably due to nanofiller content and/or oxidative changes on collagen-depleted dentin es
dc.title Bonding efficacy of an acetone/based etch-and-rinse adhesive after dentin deproteinization es
dc.type journal article es_ES
dc.subject.unesco UNESCO::CIENCIAS MÉDICAS es
dc.identifier.doi 10.4317/medoral.17717 es
dc.type.hasVersion VoR es_ES

Visualització       (863.5Kb)

Aquest element apareix en la col·lecció o col·leccions següent(s)

Mostra el registre parcial de l'element

Cerca a RODERIC

Cerca avançada

Visualitza

Estadístiques