NAGIOS: RODERIC FUNCIONANDO

Repair bond strength of composite : effect of surface treatment and type of composite

Repositori DSpace/Manakin

IMPORTANT: Aquest repositori està en una versió antiga des del 3/12/2023. La nova instal.lació está en https://roderic.uv.es/

Repair bond strength of composite : effect of surface treatment and type of composite

Mostra el registre parcial de l'element

dc.contributor.author Ghavam, Maryam es
dc.contributor.author Naeemi, Maryam es
dc.contributor.author Hashemikamangar, Sedighe Sadat es
dc.contributor.author Ebrahimi, Hooman es
dc.contributor.author KharaziFard, Mohammad J. es
dc.date.accessioned 2018-07-30T09:37:59Z
dc.date.available 2018-07-30T09:37:59Z
dc.date.issued 2018 es
dc.identifier.citation Ghavam, Maryam ; Naeemi, Maryam ; Hashemikamangar, Sedighe Sadat ; Ebrahimi, Hooman ; KharaziFard, Mohammad J.. Repair bond strength of composite : effect of surface treatment and type of composite. En: Journal of Clinical and Experimental Dentistry, 10 6 2018: 520-527 es
dc.identifier.uri http://hdl.handle.net/10550/67281
dc.description.abstract Background: By an increase in use of composite restorations, some defects are also seen in these restorations, which need to be repaired. Since complete replacement of an old restoration may compromise the tooth structure, repair of defect is a more practical approach if there is no caries recurrence. Risk of pulp injury also decreases as such. One major challenge in restoration repair is to obtain a durable bond between the new and old composite. Laser irradiation has been suggested for surface preparation of old composite. This study aimed to assess the effect of composite surface preparation with Er,Cr:YSGG laser on microtensile bond strength to new composite. Material and Methods: A total of 18 blocks were fabricated in three groups of nanohybrid, microhybrid and Beautiful II giomer measuring 4x7x7 mm and subjected to 10,000 thermal cycles between 5-55°C with 30 seconds of dwell time. The samples were randomly assigned to no surface treatment (etching and bonding) or laser plus etching and bonding groups. Composite cylinders measuring 4x7x7 mm were fabricated of Beautiful, nanohybrid and microhybrid composites on old composite surfaces and subjected to 500 thermal cycles for 50 seconds between 5-55°C with 30 seconds of dwell time. Each block was sectioned into 10 samples and they were subjected to microtensile bond strength test. Data were analyzed using ANOVA and Tukey?s test. Results: In all composites, the mean bond strength in laser subgroups was higher than that in control subgroups except for giomer, which showed lower bond strength in laser subgroup. The lowest mean bond strength was noted in repair of Z350XT with Z350XT when the surface of old composite was etched (10.92 MPa). The highest mean bond strength was noted in repair of Z250 with giomer when the old composite surface was irradiated with laser (30.55 MPa). Conclusions: Er,Cr:YSGG laser plus etching increased the bond strength in all groups except for giomer group, which showed a reduction in bond strength. es
dc.title Repair bond strength of composite : effect of surface treatment and type of composite es
dc.type journal article es_ES
dc.subject.unesco UNESCO::CIENCIAS MÉDICAS es
dc.identifier.doi 10.4317/jced.54030 es
dc.type.hasVersion VoR es_ES

Visualització       (1.049Mb)

Aquest element apareix en la col·lecció o col·leccions següent(s)

Mostra el registre parcial de l'element

Cerca a RODERIC

Cerca avançada

Visualitza

Estadístiques